![]() ![]() :54161 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key :54161 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication :54161 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key MULTI: primary virtual IP for client1/:54604: 10.8.0.6Ĭlient1/:54604 PUSH: Received control message: 'PUSH_REQUEST'Ĭlient1/:54604 send_push_reply(): safe_cap=940Ĭlient1/:54604 SENT CONTROL : 'PUSH_REPLY,redirect-gateway def1 bypass-dhcp,route 10.8.0.1,topology net30,ping 10,ping-restart 120,ifconfig 10.8.0.6 10.8.0.5' (status=1)Ĭlient1/:54604 Inactivity timeout (-ping-restart), restartingĬlient1/:54604 SIGUSR1 received, client-instance restarting MULTI_sva: pool returned IPv4=10.8.0.6, IPv6=(Not enabled) Remember to use the -duplicate-cn option if you want multiple clients using the same certificate or username to concurrently connect. MULTI: new connection by client 'client1' will cause previous active sessions by this client to be dropped. :54604 Peer Connection Initiated with :54604 :54604 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 2048 bit RSA :54604 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication :54604 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key :54604 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication :54604 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key ![]() :36786 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 2048 bit RSA :36786 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication :36786 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key :36786 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication :36786 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key :36786 WARNING: 'comp-lzo' is present in local config but missing in remote config, local='comp-lzo' ![]() :36786 WARNING: 'link-mtu' is used inconsistently, local='link-mtu 1542', remote='link-mtu 1541' This is my openvpn.log: OpenVPN 2.3.2 x86_64-suse-linux-gnu built on May 31 2013ĭiffie-Hellman initialized with 2048 bit key The connection is working via OpenVPN, but I cannot use the Internetconnection or even "ping". If your network interface is eth0, then the command should be: Use the following command: :~$ netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1Īnd finally you can view it using the eth config files. Use the following command: :~$ ip route show default via 192.168.1.1 dev eth1 proto static 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.100 metric 1 Find Default Gateway in Linux Using netstat Find Default Gateway in Linux Using IP route ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |